Micro Matic MININIMV1 kaffebryggare Bruksanvisning

Q: MININIM™ REGULATOR ADJUSTMENT HAS NO EFFECT ON PRODUCT

Regulator knob screw is loose Tighten the knob securing screw.

Q: MININIM™ REGULATOR ADJUSTMENT HAS NO EFFECT ON PRODUCT

Regulator is defective Return the unit or replace the regulator.

Q: PRODUCT HAS TOO LITTLE OR NO HEAD

Incorrect supply pressure Set gas supply pressure to 30-35 PSI. Replace empty or low-pressure gas supply bottle or if equipped check the gas generator.

Q: PRODUCT HAS TOO LITTLE OR NO HEAD

Kinked, blocked or damaged hose Check gas supply line flow. If flow is low/not present, check fittings and hoses and replace or re-route as required.

Q: PRODUCT HAS TOO LITTLE OR NO HEAD

MiniNIM™ regulator is set too low Turn the MiniNIM™ regulator clockwise using small increments approx. 1/8 turn until desired effect is achieved.

Använd läsaren nedan för att läsa Micro Matic MININIMV1 kaffebryggare bruksanvisningen. Du kan bläddra genom bruksanvisningen direkt på sidan och använda vår läsares funktioner för att hitta all viktig information om installation, användning och underhåll av denna Micro Matic kaffebryggare.

Bruksanvisning

Helskärm

Dela denna bruksanvisning Micro Matic

WhatsApp Email

Var denna bruksanvisning användbar?

Felsökning

Praktiska tips för att lösa de vanligaste problemen med Micro Matic MININIMV1.

MININIM™ REGULATOR ADJUSTMENT HAS NO EFFECT ON PRODUCT maintenance

Orsak: Regulator knob screw is loose

Lösning

Tighten the knob securing screw.

MININIM™ REGULATOR ADJUSTMENT HAS NO EFFECT ON PRODUCT maintenance

Orsak: Regulator is defective

Lösning

Return the unit or replace the regulator.

PRODUCT HAS TOO LITTLE OR NO HEAD performance

Orsak: Incorrect supply pressure

Lösning

Set gas supply pressure to 30-35 PSI. Replace empty or low-pressure gas supply bottle or if equipped check the gas generator.

PRODUCT HAS TOO LITTLE OR NO HEAD installation

Orsak: Kinked, blocked or damaged hose

Lösning

Check gas supply line flow. If flow is low/not present, check fittings and hoses and replace or re-route as required.

PRODUCT HAS TOO LITTLE OR NO HEAD performance

Orsak: MiniNIM™ regulator is set too low

Lösning

Turn the MiniNIM™ regulator clockwise using small increments approx. 1/8 turn until desired effect is achieved.

PRODUCT HAS TOO LITTLE OR NO HEAD performance

Orsak: No gas supplied to MiniNIM™

Lösning

Replace gas bottle, repair gas supply system.

PRODUCT HAS TOO MUCH HEAD AND/OR ALL FOAM AND/OR SPUTTERING AT FAUCET performance

Orsak: MiniNIM™ regulator is set too high

Lösning

Turn the MiniNIM™ regulator counter-clockwise using small increments approx. 1/8 turn until desired effect is achieved.

PRODUCT DOES NOT FLOW FROM THE FAUCET installation

Orsak: Kinked, blocked or damaged hose

Lösning

Check the liquid in and liquid out hoses for kinks or flat spots. Re-route or replace hoses as required.

PRODUCT DOES NOT FLOW FROM THE FAUCET maintenance

Orsak: Blockage in the MiniNIM™ bore due to set-up debris or solids in the product liquid

Lösning

Blow compressed gas into the product outlet to clear debris. Do not use a pin in the bore of the injector to clean out any debris, as this will likely damage it.

PRODUCT FLOWS TOO SLOWLY FROM THE FAUCET (LESS THAN 1 OZ. PER SECOND) performance

Orsak: Liquid pressure is too low

Lösning

Increase liquid pressure 30-35 PSI. This liquid pressure is required. Pressure above 35 PSI may cause canister infusion if pressurized for a period exceeding 24 hours.

PRODUCT FLOWS TOO SLOWLY FROM THE FAUCET (LESS THAN 1 OZ. PER SECOND) installation

Orsak: Liquid or product line or fitting is kinked, blocked or damaged

Lösning

Repair, replace, re-route or clear hose or fitting.

PRODUCT FLOWS TOO SLOWLY FROM THE FAUCET (LESS THAN 1 OZ. PER SECOND) maintenance

Orsak: Faucet is not completely open, defective, or blocked

Lösning

Fully open or replace/repair/clean the faucet. There are small holes in the internal disc of the stout faucet nozzle that may require periodic cleaning.

Vanliga Frågor

De vanligaste frågorna om Micro Matic MININIMV1.

Gastrycket ska sättas till 30-35 PSI för att säkerställa korrekt funktion.

Kontrollera gas- och vätskeledningar för kink eller blockering. Kontrollera att MiniNIM™-regulatorn är korrekt inställd. Om det finns debrisanhopning i injektorn, använd tryckluftsblås för att rensa den utan att använda en nål.

Vänd MiniNIM™-regulatorn moturs i små steg på cirka 1/8 varv tills önskad effekt uppnås.

Vätsketrycket ska vara 30-35 PSI. Tryck över 35 PSI kan orsaka kanninfusion om det pressureras i mer än 24 timmar.

Kontrollera att skruven på regulatorknappen är åtsträckad. Om regulatorn är defekt måste den bytas ut eller enheten returneras.

Hjälp

Har du frågor om kaffebryggare MININIMV1 från Micro Matic? Ställ dem direkt till vår expert! Du får information, praktiska tips och skräddarsydda lösningar på bara några sekunder.

Nedan hittar du bruksanvisningar för kaffebryggare som liknar MININIMV1. Prova även att se alla Micro Matic kaffebryggare bruksanvisningar

Cecotec

Power Espresso 20 Pecan