Brightness or contrast set incorrectly, or lamp needs replacement. Adjust Brightness setting in Configuration menu. Adjust Contrast setting. Check if lamp is ready for replacement.

Epson EH-TW5600 videoprojektor Bruksanvisning

Q: Epson EH-TW5600 - Auto Iris Error

Auto Iris system malfunction detected. Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Q: Epson EH-TW5600 - Fan Error

Fan malfunction detected. Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Q: Epson EH-TW5600 - Internal Error

The projector has malfunctioned. Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Q: Epson EH-TW5600 - Power Err. (Ballast)

Power supply or ballast error detected. Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Q: Epson EH-TW5600 - Sensor Error

Sensor malfunction detected. Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Använd läsaren nedan för att läsa Epson EH-TW5600 videoprojektor bruksanvisningen. Du kan bläddra genom bruksanvisningen direkt på sidan och använda vår läsares funktioner för att hitta all viktig information om installation, användning och underhåll av denna Epson videoprojektor.

Bruksanvisning

Helskärm

Dela denna bruksanvisning Epson

WhatsApp Email

Var denna bruksanvisning användbar?

Felkoder

Nedan hittar du felkoderna för Epson EH-TW5600.

Auto Iris Error other

KRITISK

Auto Iris system malfunction detected.

Lösning

Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Fan Error fan

KRITISK

Fan malfunction detected.

Lösning

Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

High Temp Error temperature

KRITISK

Internal temperature is too high - projector overheating. Lamp turns off automatically and projection stops.

Lösning

Wait about five minutes for fan to stop, then disconnect power cord. Ensure at least 20 cm clearance between exhaust vent and wall. Clean clogged air filter. When using at altitude of 1500 m or more, set High Altitude Mode to On. If problem persists, contact local dealer or Epson repair center.

High Temp Warning temperature

VARNING

Temperature warning - projector can continue projecting but may stop automatically if temperature rises further.

Lösning

Ensure at least 20 cm clearance between projector exhaust vent and any wall. Clean the air filter if clogged. When using at altitude of 1500 m or more, set High Altitude Mode to On.

Internal Error other

KRITISK

The projector has malfunctioned.

Lösning

Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Lamp Error other

KRITISK

Problem with the lamp, or it failed to turn on. Lamp Failure or Lamp Cover Open.

Lösning

Disconnect the power cord and check if the lamp is cracked. If not cracked, reinstall the lamp and turn on the power. If reinstalling does not fix the problem or if the lamp is cracked, contact your local dealer or Epson repair center. Check that the lamp cover has been properly closed.

Power Err. (Ballast) power

KRITISK

Power supply or ballast error detected.

Lösning

Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Sensor Error sensor

KRITISK

Sensor malfunction detected.

Lösning

Remove the power plug from the electrical outlet and contact your local dealer or nearest Epson repair center.

Felsökning

Praktiska tips för att lösa de vanligaste problemen med Epson EH-TW5600.

No images appear power

Orsak: Projector not turned on, power cord not connected, indicators switched off, no input signal, incorrect configuration settings, or connection made while power was already on.

Lösning

Press the power button on remote control or control panel. Connect the power cord. Disconnect and reconnect projector power cord. Verify connected device is turned on. Reset all configuration settings. If connecting computer signals, turn off power to both devices and turn back on.

Moving images being projected from a computer are not projected connectivity

Orsak: Computer set to output to both external output and LCD monitor simultaneously.

Lösning

Switch computer so image signal is set to external output only. Check computer documentation for specifications.

Not supported is displayed quality

Orsak: Image signal frequency and resolution do not correspond to projector's supported modes.

Lösning

Check image signal resolution in Configuration menu and verify it corresponds to projector resolution. Confirm image signal frequency and resolution match the mode.

No Signal is displayed connectivity

Orsak: Cables not connected correctly, incorrect input port selected, connected device not turned on, or image signals not being output to projector.

Lösning

Check all cables are securely connected. Switch image with source buttons on remote control. Turn on connected device. Set computer to external output only, not LCD monitor. Turn power off and back on for both devices if connected while powered on.

Images are fuzzy or out of focus quality

Orsak: Focus not adjusted, lens cover closed, projector at incorrect distance, or condensation on lens.

Lösning

Adjust the focus. Open the lens cover. Check recommended projection range. If condensation has formed, allow projector to warm up in the room about one hour before use. Turn off projector and disconnect power cord, then leave to dry.

Interference or distortion appears in images quality

Orsak: Cables not connected correctly, extension cable in use, Sync and Tracking not adjusted correctly, or incorrect resolution selected.

Lösning

Check all cables are securely connected. Avoid using extension cables as they may cause electrical interference. Adjust Tracking and Sync settings from Configuration menu. Ensure computer outputs signals compatible with projector resolution.

Image is truncated (large) or small, or only part of image is projected quality

Orsak: Incorrect Aspect selected, Position not adjusted correctly, or incorrect resolution selected.

Lösning

Select aspect mode to match input signal. Adjust Position setting in Configuration menu. Ensure computer outputs signals compatible with projector resolution.

Image colors are not right quality

Orsak: Contrast or color settings not adjusted correctly.

Lösning

Adjust Contrast setting in Configuration menu. Adjust Advanced color setting in Configuration menu.

Images appear dark quality

Orsak: Brightness or contrast set incorrectly, or lamp needs replacement.

Lösning

Adjust Brightness setting in Configuration menu. Adjust Contrast setting. Check if lamp is ready for replacement.

Projection stops automatically temperature

Orsak: Projector overheating due to high internal temperature.

Lösning

Wait about five minutes for the projector to cool down. Ensure proper ventilation with at least 20 cm clearance from walls. Clean air filter if clogged. At high altitudes (1500 m or more), enable High Altitude Mode.

The projector does not turn on power

Orsak: Power not connected or configuration issues.

Lösning

Verify power cord is connected. Press power button on remote control or control panel. If indicators are off, disconnect and reconnect power cord.

Remote control does not respond connectivity

Orsak: Remote control not functioning properly.

Lösning

Check remote control batteries and connections. Verify line of sight to projector's remote sensor.

Cannot project correctly in 3D quality

Orsak: 3D settings not configured correctly or incompatible content.

Lösning

Check 3D configuration settings. Verify content is compatible with 3D projection.

HDMI Link does not function connectivity

Orsak: HDMI Link settings not enabled or devices not compatible.

Lösning

Enable HDMI Link in Configuration menu. Verify connected devices support HDMI Link functionality.

Device name is not displayed under device connections connectivity

Orsak: Wireless LAN or Bluetooth connection not established.

Lösning

Check Wireless LAN Power is set to On in Network menu. Verify device is in pairing mode. Restart both projector and device.

Cannot access network via wireless LAN connectivity

Orsak: Wireless LAN not enabled or network configuration incorrect.

Lösning

Verify Wireless LAN Power is set to On in Network menu. Check network settings and credentials. Select Off and then On again in Wireless LAN Power setting if experiencing errors.

Image contains static during network projection connectivity

Orsak: Network interference or weak signal.

Lösning

Move projector closer to router. Reduce network traffic. Check for other wireless interference sources.

Cannot connect using Screen Mirroring connectivity

Orsak: Screen Mirroring not enabled or device not compatible.

Lösning

Verify Screen Mirroring is enabled in Configuration menu. Check device compatibility. Ensure both devices are on same network.

Image contains static during Screen Mirroring connection connectivity

Orsak: Wireless interference or network congestion.

Lösning

Move projector closer to wireless router. Reduce other network traffic. Check for wireless interference sources.

Cannot connect Bluetooth device connectivity

Orsak: Bluetooth not enabled or device not in pairing mode.

Lösning

Enable Bluetooth in projector settings. Put Bluetooth device in pairing mode. Check device compatibility.

Audio and connection for Bluetooth device disconnects connectivity

Orsak: Bluetooth connection instability or interference.

Lösning

Move device closer to projector. Remove sources of wireless interference. Re-pair Bluetooth device. Check device battery level.

No audio, or audio is too low quality

Orsak: Volume set too low, audio output not configured correctly, or muted.

Lösning

Increase volume using remote control. Check audio output settings in Configuration menu. Verify audio input source is selected. Unmute audio if muted.

Cannot make settings on control panel other

Orsak: Control panel locked or projector in standby mode.

Lösning

Unlock control panel if locked. Turn on projector. Check that power is supplied to control panel.

Slideshow does not start quality

Orsak: No images selected for slideshow or slideshow settings incorrect.

Lösning

Select images for slideshow. Check slideshow configuration settings. Verify image files are supported format.

Vanliga Frågor

De vanligaste frågorna om Epson EH-TW5600.

Se den rekommenderade projektionsräckvidden på sida 15 i manualen. Projektorn måste placeras på rätt avstånd för optimal bildstorlek och fokus.

Lampan bör bytas när indikatorn visar 'Replace Lamp'. Det är viktigt att byta lampan så snart som möjligt då lampan kan explodera om den fortsätts att användas i detta tillstånd.

Om projektorn blir för varm: se till att det finns minst 20 cm utrymme mellan projektorn och vägg, rengör luftfiltret om det är igensatt, och om du använder projektorn på höga höjder (1500 m eller mer), aktivera High Altitude Mode. Om problemet kvarstår, kontakta din lokala återförsäljare eller Epson.

Det finns ett problem med lampan eller den misslyckades att tändas. Kontrollera om lampan är sprucken. Om den inte är sprucken, installera om den. Om problemet kvarstår eller om lampan är sprucken, kontakta din lokala återförsäljare eller Epson reparationscenter.

Uppvärmingstiden är cirka 30 sekunder. Under denna tid är strömbrytningen inaktiv.

Kontrollera att projektorn är påslagen, strömkabeln är ansluten, indikatorerna tänds, inspelingsenheten är påslagen, och att rätt ingångsport är vald. Återsätt alla inställningar om problemet kvarstår.

Se sida 91 i manualen för instruktioner om hur du rensar luftfiltret. Ett igensatt luftfilter kan orsaka överhettning och projection kan stoppas automatiskt.

Ja, men när du använder projektorn på höjder av 1500 m eller mer, måste du aktivera High Altitude Mode från Extended - Operation - High Altitude Mode (sida 71).

Justera fokus enligt instruktionerna på sida 28. Se också till att linsräkningen är öppen och att projektorn är på rätt avstånd. Om imorn är kondenserad, låt projektorn sitta i rummet i cirka en timme innan användning.

Alla operationer är inaktiverade under nedkylning. Projektorn återgår till standby-läge när nedkylningen är slutförd. Om strömkabeln kopplas bort under nedkylning, vänta tills lampan har kallnat tillräckligt (cirka 10 minuter) innan du återansluter kabeln.

Hjälp

Har du frågor om videoprojektor EH-TW5600 från Epson? Ställ dem direkt till vår expert! Du får information, praktiska tips och skräddarsydda lösningar på bara några sekunder.

Nedan hittar du bruksanvisningar för videoprojektor som liknar EH-TW5600. Prova även att se alla Epson videoprojektor bruksanvisningar